How to configure cisco wireless access point via console. Cisco IOS Configuration Guide for Autonomous Aironet Access Points Cisco IOS Release 15.3(3)JAB

See the LSC summary by entering this command:. Each CDP enabled device sends information about itself to its immediate neighbor. Click the name of the access point for which you want to configure link latency. Step 4 Enter the case-sensitive password Cisco and press Enter. The MAC address can be found on the label on the bottom of the access point such as c. The web-browser interface is fully compatible with Microsoft Internet Explorer version 6.

 

Configuring the Access Point for the First Time. For information on logging into the AP through the CLI refer to Accessing the CLI.The access point maintains a list of backup controllers and periodically sends primary discovery requests to each entry on the list.

 

You can configure all the settings described in this chapter using the CLI, but it might be simplest to browse to the wireless device web-browser interface to.If you choose to follow this suggested flow and enable

 

Step 2 Enter the wireless device IP address in the browser address line and press Enter. An Enter Network Password window appears. Step 3 Enter.From the Local Mode AP Fast Heartbeat Timer State drop-down list, choose Enable to enable the fast heartbeat timer for access points in local mode or choose Disable to disable this timer.

 

Follow these steps to open the CLI by connecting to the access point console port: Step 1 Connect a nine-pin, male-to-female, straight-through DB-9 serial cable.Switch configure terminal.

 

To obtain the access point/bridge's new IP address, you can use the show interface bvi1 CLI command. Obtaining and Assigning an IP Address. To browse to the.The access point reboots and rejoins the controller, and the static IP address that you specified in Step 1 is pushed to the access point.

 

Configuring the Access Point for the First Time forum? You can configure VLAN tagging on the Ethernet interface either directly on the AP console or through the controller. The configuration is.New Folder Cancel OK.

 

Cisco IOS Configuration Guide for Autonomous Cisco Aironet Access Points - Release 15.3(3)JBB forum? The Cisco AG is a powerful business-grade wireless access point (AP) with lots of features. Learn how to configure one from scratch.Not Available.

 

After you complete the initial configuration settings, CONSOLE. POE. 2. Cisco Business Wireless access points can be mounted in several.Step 7 When the All APs page reappears, click the name of the access point again.

 

After you determine or assign the wireless device IP address, you can browse to the wireless device Express Setup page and perform an initial configuration:.

 

Note You do not need a special crossover cable to connect your PC to the power injector; you can use either a straight-through cable or a crossover cable.

 

For more information, see AAA Administration.

 

The configurable settings include:.

 

Beginning in privileged EXEC mode, follow these steps to create an

 

The configuration information file is an XML file, containing the following information:.

 

You can configure all the settings described in this chapter using the CLI, but it might be simplest to browse to the wireless device's web-browser interface to complete the initial configuration and then use the CLI to enter additional settings for a more detailed configuration.

 

Check your PC operating instructions for detailed instructions for your operating system.

 

The following are supported for web authentication and WebAdmin based on the configuration:.

 

Support for

 

Step 2 With the power cable disconnected from the power injector, connect your PC to the power injector using a Category 5 Ethernet cable.

 

The configurable settings include: Host Name—The host name, while not an essential setting, helps identify the wireless device on your network.

 

Because

 

Instead of tracking separate IP addresses for the wireless device's Ethernet and radio ports, the network uses the BVI.Forum How to configure cisco wireless access point via console

 

Step 3 Enter your username in the User Name field.

 

Configure a static IP address on the access point by entering this command:.

 

Step 4 Optional Disable

 

Optional —Enter a description for the credentials profile.

 

For example, to configure 80 Mhz channel width: ap configure terminal ap config interface dot11Radio 1 ap config-if channel width 80 ap config-if end Power Management for